Advertising
16
We offer you a Owner's Manual of Weider PRO 3750 (No. WESY26330): PDF file 6.29 Mb, 33 pages. On this page you can download this Owner's Manual and read it online. Also, you will be able to ask a question about Weider PRO 3750 (No. Download WEIDER PRO 4850 User Manual. WEIDER PRO 4850. Related Manuals for WEIDER PRO 4850. Fitness Equipment Weider 831.153930f User Manual 35 pages. Weight system. PRO 4850 SYSTEM WESY3964 - read user manual online or download in PDF format. Pages in total: 40. Weider PRO 4850 SYSTEM WESY3964 Likes 0 Downloads 0 Show. View and Download WEIDER PRO 4850 user manual online. Weight system exerciser. PRO 4850 Fitness Equipment pdf manual download. Also for: Pro 4850, 831.153932.
41.
Remove the preattached 90mm Pulley (not
shown) from the “U”-bracket (64).
shown) from the “U”-bracket (64).
Attach the end of the Leg Lever Cable (75) to the
“U”-bracket (64) with an M8 Washer (90) and an M8
Nylon Locknut (86).
“U”-bracket (64) with an M8 Washer (90) and an M8
Nylon Locknut (86).
Note: Do not completely
tighten the Locknut; it should be threaded only
two turns onto the end of the Cable, as shown
in the inset drawing.
two turns onto the end of the Cable, as shown
in the inset drawing.
Weider Pro 4850 Exercises
42.
Locate the Swivel Low Cable (72), which is the
only remaining cable that has an eyelet on one
end and a ball on the other end. Route the eyelet
end of the Cable through the cage on the Long
Base (106) and through the Swivel Upright (5) as
shown.
only remaining cable that has an eyelet on one
end and a ball on the other end. Route the eyelet
end of the Cable through the cage on the Long
Base (106) and through the Swivel Upright (5) as
shown.
Make sure the Cable is over the short
bar in the cage.
Attach a 90mm Pulley (78) to the indicated bracket
on the Long Base (106) with M10 x 45mm Bolt (93)
and an M10 Nylon Locknut (87).
on the Long Base (106) with M10 x 45mm Bolt (93)
and an M10 Nylon Locknut (87).
Make sure the
Cable is in the groove of the Pulley.
43. Wrap the Swivel Low Cable (72) under a 90mm
Pulley (78). Attach the Pulley to the indicated brack-
et on the Long Base (106) with an M10 x 45mm
Bolt (93) and an M10 Nylon Locknut (87).
et on the Long Base (106) with an M10 x 45mm
Bolt (93) and an M10 Nylon Locknut (87).
39
40
41
42
92
64
75
78
90
72
87
62
93
86
43
75
91
91
87
3
119
113
106
78
Cage
93
87
5
72
106
93
78
87
75
39. Route the Leg Lever Cable (75) under a 115mm
Pulley (119). Attach the Pulley and a Large Cable
Trap (113) to the indicated side of the Butterfly
Upright (3) with an M10 x 95mm Bolt (92), two M10
Washers (91), and an M10 Nylon Locknut (87).
Make sure that the Large Cable Trap is turned to
hold the Cable in the groove of the Pulley.
Trap (113) to the indicated side of the Butterfly
Upright (3) with an M10 x 95mm Bolt (92), two M10
Washers (91), and an M10 Nylon Locknut (87).
Make sure that the Large Cable Trap is turned to
hold the Cable in the groove of the Pulley.
40. Wrap the Leg Lever Cable (75) over a 90mm Pulley
(78). Attach the Pulley to the Double “U”-bracket
(62) with an M10 x 45mm Bolt (93) and an M10
Nylon Locknut (87).
(62) with an M10 x 45mm Bolt (93) and an M10
Nylon Locknut (87).
75
86
Advertising
Popular Brands
Popular manuals
Advertising
18.
Locate and open the parts bags labeled “CABLE
ASSEMBLY” and “PULLEYS.”
ASSEMBLY” and “PULLEYS.”
Lubricate the M10 x 165mm Bolt (95) with grease.
Attach the Swivel Cage (76) to the Swivel Carriage
(46) with the Bolt and an M10 Nylon Locknut (87).
Attach the Swivel Cage (76) to the Swivel Carriage
(46) with the Bolt and an M10 Nylon Locknut (87).
Locate the Swivel High Cable (74), which is
3200mm long and has a ball on one end and a
threaded bolt on the other end. Remove the
upper 90mm Pulley (78) from the Swivel Cage (76).
Wrap the Cable around the Pulley. Reattach the
Pulley to the Swivel Cage with the M10 x 45mm
Bolt (93) and the M10 Nylon Locknut (87).
3200mm long and has a ball on one end and a
threaded bolt on the other end. Remove the
upper 90mm Pulley (78) from the Swivel Cage (76).
Wrap the Cable around the Pulley. Reattach the
Pulley to the Swivel Cage with the M10 x 45mm
Bolt (93) and the M10 Nylon Locknut (87).
11
16. Press a 40mm x 50mm Inner Cap (21) into the Right
Butterfly Arm (26). Wet the lower end of the Arm and
a Long Pad (54) with soapy water. Slide the Long
Pad onto the Arm.
a Long Pad (54) with soapy water. Slide the Long
Pad onto the Arm.
Attach the Press Handle (27) to the Right Butterfly
Arm (26) with two M8 x 20mm Button Head Screws
(51). Slide the Long Pad (54) down so that the bot-
tom is flush with the lower end of the Arm. Wet the
Press Handle with soapy water. Slide a Long
Handgrip (28) onto the Press Handle. Press a 25mm
Round Inner Cap (29) into the Press Handle.
Arm (26) with two M8 x 20mm Button Head Screws
(51). Slide the Long Pad (54) down so that the bot-
tom is flush with the lower end of the Arm. Wet the
Press Handle with soapy water. Slide a Long
Handgrip (28) onto the Press Handle. Press a 25mm
Round Inner Cap (29) into the Press Handle.
Lubricate an M10 x 50mm Bolt (100) with grease.
Attach a Pivot Bracket (70) to the Right Butterfly
Arm (26) with the Bolt and an M10 Nylon Locknut
(87).
Attach a Pivot Bracket (70) to the Right Butterfly
Arm (26) with the Bolt and an M10 Nylon Locknut
(87).
Do not overtighten the Locknut; the Pivot
Bracket must be able to pivot easily. Repeat this
step with the Left Butterfly Arm (25).
step with the Left Butterfly Arm (25).
17. Lubricate an M10 x 80mm Button Head Bolt (104)
and both sides of two Plastic Washers (56) with
grease. Attach the Right Butterfly Arm (26) to the
Butterfly Frame (47) with the Bolt, the two Plastic
Washers, two Butterfly Caps (57), two M10
Washers (91), and an M10 Nylon Locknut (87) as
shown.
grease. Attach the Right Butterfly Arm (26) to the
Butterfly Frame (47) with the Bolt, the two Plastic
Washers, two Butterfly Caps (57), two M10
Washers (91), and an M10 Nylon Locknut (87) as
shown.
Make sure that the recessed sides of the
Plastic Washers are fitted over the welded bush-
ing in the Butterfly Arm. Do not overtighten the
Locknut; the Butterfly Arm must be able to pivot
easily.
ing in the Butterfly Arm. Do not overtighten the
Locknut; the Butterfly Arm must be able to pivot
easily.
Repeat this step with the Left Butterfly Arm (25).
16
CABLE ASSEMBLY
74
18
78
87
93
76
87
17
IMPORTANT: Refer to the Cable Identification
Chart on page 26 for help identifying the
cables. Do not overtighten the bolts and
nuts attaching the pulleys. The pulleys must
be able to turn freely.
Chart on page 26 for help identifying the
cables. Do not overtighten the bolts and
nuts attaching the pulleys. The pulleys must
be able to turn freely.
26
47
87
56
104
91
57
57
91
25
21
100
Lubricate
70
87
26
25
51
29
28
27
54
95
46
Advertising
Popular Brands
Popular manuals